parts for ATVs HSUN
parts for ATV Kazuma, Jaguar
Piston set 125cc - 54mm (154FMI) C: 19.5mm D: 54.00mm d: 14mm H: 2.5mm L: 39.5mm
Chain cover type 4 (110cc) length: 260 mm width: 130mm / 150mm depth: 57mm pitch for screws: 145mm / 165mm
Magneto - cover (rotor) 49/110 / 125cc (Typ1) Typ1
Piston set 125cc for ATVs (Avenger,Commander)
Clutch plates - complete set 6 + 5 (200 / 250cc)
Shock absorber front 110 / 125cc overall length: 280mm eye to eye length: 250mm diameter for screw: 10mm mounting width: 20.5mm spring width: 57mm
Magnet cover with upper starter type3 (110 / 125cc) For engine type 154FMI
Shock absorber front 110 / 125cc overall length: 280mm eye to eye length: 250mm diameter for screw: 10mm mounting width: 20.5mm spring width: 57mm
CDI control unit for Shineray 300cc STXE ATV 6 PIN
Magnet cover with bottom starter (110 / 125cc)
Magnet cover with upper starter type2 (110 / 125cc)
Steering rod complete for quad bike GSMoon 260cc (Sport 300) M12 rod thread
Magnet cover with upper starter type1 (110 / 125cc)
Front silencer for ATV Barbarossa 800W - 27cm
Magneto - rotor for Avenger, Commander 125cc
Front wheel hub with a pitch of 89mm dimensions shown in the figure
Carburettor 110ccc / 125cc the carburetor includes a fuel cock cable choke
Carburetor 110 / 125cc Cross PZ20 slide diameter 17mm
Gasket under the head and under the cylinder HSUN 700cc
Freewheel bearing with Shineray 200ST gear
Induction coil complete for ATVs with Linhai 260cc motor
Front brake complete Shineray 250STXE/250STIX - right
Fluid brake lever (right) - type2 the classic size of the brake fluid container
Carburettor 110 / 125cc cable choke control slide diameter 18mm nozzle 90
UNI brake cylinder - type3 mounting spacing: 38mm length: 96.1mm width: 58mm
Fluid brake lever (right) - type4 the classic size of the brake fluid container
Fluid brake lever (left) - scooter M10 thread for mirror
Fluid brake lever (right) - type3 the classic size of the brake fluid container
Piston sda 250cc 67mm piston pin 16mm Bashan, Shineray, Lyda, etc.
Fluid brake lever (right) - type1 smaller brake fluid container
Carburettor 110 / 125cc cable choke control slide diameter 15mm
Carburettor 110cc / 125cc Cross PZ22 choke control manually slide diameter 17mm
Plastic upper part of the front mask for ATV Commander 125cc
Chain for ATVs 110/125/150/200/250cc chain 520 YBN 130 articles
Gasket under the head and under the cylinder HSUN 500cc
Magneto coils 200 / 250cc type2 12 coils 5 PIN 93mm outside diameter 31mm coil width
Electrical installation for Barbarossa 125cc ATV
Electrical installation for ATV Hunter 125cc
Engine crankcase scooter GY6 4t 125 / 150cc - right
Gearbox 110 / 125cc - type2 (automatic without reverse)
Shock absorber rear ATV 110/125 (27.5cm) length from eye to eye 27.5 cm
Idle bearing 200cc / 250cc We recommend that you also buy a freewheel gear for the freewheel bearing, which is usually already squeezed.
Variator front part complete, including rollers 125 / 150cc GY6
Leopard lower arm 150 / 250cc Offroad 150cc EEC
Front brake complete 110 / 125cc left right
Plastic treads L + R for ATV Commander 125cc
Intake + exhaust valves 260cc suction valve length: 94mm exhaust valve length: 92.7mm suction valve diameter: 34mm exhaust valve diameter: 28.6mm
Carburetor 200 / 250cc with choke control by manual PZ27
Starter for quads 150cc and scooters 125 / 150cc mounting holes span: 78.5mm holes diameter: 6.5 mm overall length: 132mm shaft diameter: 11.5 mm shaft length: 18 mm Number of teeth: 9 diameter for O-ring: 29.9x16mm total diameter: 59 mm
UNI two-piston brake mounting spacing: 95mm dimensions in the picture
UNI two-piston brake mounting spacing: 44mm dimensions in the picture
Engine - engine cylinder 110 / 125cc 52.4mm