close |
Gasoline hose with a diameter of 5mm. price for 0.5 ordinary meter
Gasoline hose with a diameter of 5mm. price for 0.5 ordinary meter
Gasoline hose with a diameter of 6mm. price for 0.5 ordinary meter
Clutch spring for ATVs with 200 / 250cc engine capacity
Crank wedge 200 / 250cc length 14mm width 4mm height 4mm
Spring for oil screen Leopard 150cc, BS150cc
Engine cover type 2 (49/110/125 / 250cc)
Gasket under the cylinder 200cc for air-cooled engine
Radiator hose straight 12mm long 30cm with wire protection
Radiator hose curved 12mm long 46cm with wire protection
Valves - lower + upper springs for ATVs with engine capacity 200cc, 250cc, 260cc
Gasket under the cylinder 250cc - water cooled engine
Engine bolts 4pcs 250cc H2O length 143mm thread M8 thread length 21mm
Oil dipstick for ATVs and motorcycles 200cc and 250cc length from thread end: 115mm overall length: 128.9mm thread: M19
Transmission Forks - Axle (BS200S-7)
Head gasket 200 / 250cc - hydrogen (67mm) three-layer
Piston rings 200cc (63.5mm) for 163ML engine
Head gasket for water-cooled engine with engine capacity 200 / 250cc - 64.2mm
Lower valve rocker for quads 200 / 250cc
Shineray 250STIXE - 2PIN speed sensor
Clutch lever with switch 200/250 / 300cc
Piston rings set 200cc for piston 62.4 and 62.8mm for piston groove 1mm
Head and cylinder gasket 200cc - Bashan (63.5mm) dimensions shown in the figure
Piston rings set 200cc for piston 62.4mm for piston groove 1.2mm
Piston rings set 200cc for piston 62.4 and 62.8mm for piston groove 1.2mm
Valves - valve distribution rods 200 / 250cc (pair) length 153mm diameter 6mm
Mounting hole cover for starter 200 / 250cc
Mounting hole cover for starter 200 / 250cc - air
Piston 200cc 62.4mm groove for rings 1mm for piston pin 15mm
Set of clutch plate plates - 5pcs
Intake + exhaust valves 250cc type2 suction length 91.8mm exhaust valve length: 91.4mm suction valve diameter: 30.3mm exhaust valve diameter: 25mm shaft diameter 5.5mm
Intake + exhaust valves 200cc suction length 90mm exhaust valve length: 89mm suction valve diameter: 32mm exhaust valve diameter: 27mm
Intake + exhaust valves 200cc suction length 90.6 mm exhaust valve length: 90.4 mm suction valve diameter: 31.5 mm exhaust valve diameter: 27 mm shaft diameter: 5.5mm
Engine cover - Head cover (BS200S-7)
Intake and exhaust valves Zongshen 250cc Cross / Bashan BS250S suction length: 89.5 mm exhaust valve length: 89.5 mm suction valve diameter: 31.5 mm exhaust valve diameter: 27 mm shaft diameter: 5.5mm
Starter gear - counterpart (Bashan200) smaller gear 16zb. larger gear 16zb.
Gasket - complete set 200cc vodka (63,5mm)
Piston set 200cc (63.5mm) for 163ML engine 63.50 / 15 / 22.5
Valves - rocker arms set 250cc Shineray 250STIX
Clutch plates - complete set 6 + 5 (200 / 250cc)
Fan for ATV Bashan BS200 and BS250 plastic
Piston sda 250cc 67mm piston pin 16mm Bashan, Shineray, Lyda, etc.
Idle bearing 200cc / 250cc We recommend that you also buy a freewheel gear for the freewheel bearing, which is usually already squeezed.
Engine cover right side (BS200S-7)
Water pump complete for ATVs with 200 / 250cc engine capacity
Engine cover at starter left side (200 / 250cc) - type1
Engine - cylinder 200cc for engine 163ML (complete set without seal)
Starter 200 / 250cc - 11zb Typ1 dimensions shown in the figure
Starter for engines with a capacity of 200 / 250cc 9 teeth dimensions in the picture
Starter 200 / 250cc black - 11zb dimensions shown in the figure
Engine - 250cc cylinder for water-cooled engine
Engine cover (crankcase) for engine 200cc and 250cc - waterman left and right side
Crank complete for ATVs with 200cc - H2O engine dimensions shown in the figure
Crank complete for ATVs with 250cc - H2O engine capacity dimensions shown in the figure